O  Lansdale in the News

Go to News

Is Part Standardization a Thing of the Past?


Is Part Standardization a Thing of the Past?
Palm Springs, California
February 2, 2005

by W. Lee Mathiesen

Is Part Standardization a Thing of The Past?

The switch from MIL-M38510 (QPL) to MIL-PRF-38535 (QML) has created a condition where military standardized parts do not conform to "Best Commercial Practices" and may even violate current Configuration Management practices. This paper will take you through the historical changes that have led to the dilution of requirements within MIL-PRF-38535 and will show how the DLA has tailored this document to create this condition against the advice of both users and manufacturers of the products.

A History of product specifications:

Originally there were SCD's (source control drawings): These documents defined the environmental, electrical, marking, packaging and processing requirements for the parts. The problem with SCDs was that multiple NSNs were created for essentially the same part number.

Then Military Standard parts were Born. MIL-M-38510 (General Specification For Microcircuits) defined the Quality System, wafer processing, assembly and package, qualification, quality conformance Inspection requirements for all "slash sheet" and "SMD" parts. It also defined Microcircuit Groups that were based on the device technology. The major advantage was that with standardized parts there was only one NSN per part. Parts were listed on the Qualified Parts List (QPL).

M38510/XXX and 5962-XXXXX became the standard part numbers. The individual device specifications defined the electrical test requirements so that multiple manufacturers could qualify the same product to a single specification (ie. TI, National and Motorola 5400 TTL although manufactured slightly differently would be qualified under the same part number). Microcircuit group numbers for all parts on the slash sheet were defined in Section 3 "Requirements".

The system changed when MIL-PRF-38535 (General Specification for Integrated Circuit Manufacturing) QML(Qualified Manufacturing Line) was created. QML is a performance specification meaning it is descriptive not prescriptive, with most appendices providing guidelines not true requirements. QML gives the device manufacturer the flexibility to eliminate non value added testing based on statistical data. The specification is intended to document "Best Commercial Practices". Many of the definitions in MIL-M-38510 were changed or eliminated, many of the requirements were removed and new definitions were added. The electrical test requirements are still covered by the M38510/XXX and 5962 -XXXXX specifications.

As stated within the main body of MIL-PRF38535 many of the definitions previously contained in MIL-M-38510 were either changed or deleted. Notable among these are what has happened to the definitions of device type and microcircuit group. The previous definition of device type that required parts being electrically and functionally interchangeable at the die or substrate level has been dropped in the new definition. The definition of microcircuit group, which required the product be of the same basic circuit technology has been deleted altogether. Both of these definitions within appendix A of MIL-PRF-38535 are very similar to the old requirements of MIL-M-38510, however Appendix A of MIL-PRF-38535, is not required for QML manufacturers (although they are still required for class M, MIL-STD-883 suppliers). Table A-VI, which numbers Microcircuit groups, is also still in Appendix A and defines a Standard TTL Gate to be in Microcircuit group 1; it also states that a BiCMOS gate is in group 125.

So what do these changes mean to the users and manufacturers? Currently a part which is manufactured to be compliant to MIL-STD-883 Paragraph 1.2.1 must follow the original requirements of MIL-M-38510 as now defined in Appendix A of MIL-PRF-38535. A MIL-PRF-38535 QML manufacturer does not have to comply to the requirements of Appendix A.

So is this a problem? One QML manufacturer has been given special allowance by DLA/DSCC to supply a 1.5 micron BiCMOS part to the same part number as a 7 micron gold doped Bipolar TTL part, even though the slash sheet defines the part as being in Microcircuit group 1 instead of 125, and electrical testing shows the parts respond differently than the original over the military temperature range. (Go to the Lansdale website http://www.lansdale.com/gemhtml/wkparts.htm to view actual test data for 5 different part numbers.) No other manufacturers are allowed to do this, as all changes they make in device technology require a part number change.

Other new definitions within MIL-PRF-38535 include 6.4.24 Form, 6.4.25 Fit, and 6.4.26 Function. Form as defined in MIL-PRF-38535 defines only physical and visual parameters and doesn't mention the device technology. Fit refers only to the ability to physically interface, Function refers to the action or actions an item is designed to perform which has been interpreted as strictly specification requirements without any "undocumented" parameters.

Is MIL-PRF-38535 truly best commercial practices? The EIA Engineering Aerospace Qualified Electronic Component (AQEC) requirements document which will become the best commercial practices for avionics parts doesn't think so. It specifically states that parts of different device technologies shall not be furnished under the same part number because they are not the same Form, Fit, and Function. What this means is that QML devices which are capable of being supplied via the GEM program as non-Gem devices shall not be allowed as AQEC devices.

In May of 2003 a joint letter from the JC13.2 and the G-12 committees was written to the DLA. This letter stated that although there is benefit to the GEM program supporting obsolete integrated circuits for weapon system logistics, they were very concerned about the re-use of existing standardized part numbers. One of the basic principals of Configuration Management states that if Form, Fit, or Function of an item changes, you must change the associated item number. In the case of GEM emulated devices, the form because of the device technology clearly changes and with that, the potential exists for differences in unspecified or untested parameters (functional performance, ESD, radiation hardness, etc). G-12 unanimously passed the following motion:

"G-12 does not support an older technology product being emulated with a newer technology having the same part number because it is not identical in Form, Fit, and Function."

The JC13.2 committee passed a similar motion to support the G-12 position.

Is Part Standardization a Thing of The Past?


MIL-PRF-38535 has lost sight of the fact that these parts are being used in military weapon systems, instead it has focused on the manufacturing systems used to produce them. The MIL-M-38510 specification did not allow parts emulated using a different device technology to use the same part number as original devices, however, it appears that MIL-PRF-38535 (QML) has been written specifically to allow this, even though it violates "Best Commercial Practices" as defined in the EIA specification for AQEC parts and Configuration Management definitions from both the G-12 and JC13.2 committees.

If MIL-PRF-38535 does not come back in line with "Best Commercial Practices" and Configuration Management practices, more manufacturers will stop using it.

Although emulation of truly unprocurable parts is a good thing for weapons system logistic support, these parts should not have the same part number because they "Just Aren't the Same".

contact & support

phone: (602) 438-0123
fax: (602) 438-0138
email: lansdale@lansdale.com ...

from the president

After manufacturing mission-critical, hi-rel military and commercial semiconductors for over 40 years, Lansdale Semiconductor has expanded its product offerings by manufacturing some of the electronic component industry’s most popular, and in demand, ...

>read more

RoHS compliance

Certificate of Compliance - ROHS and REACH Declaration by Lansdale Semiconductor, IncStatement on the use of Conflict Metals by Lansdale Semiconductor, Inc Due to increased environmental concerns around the world, semiconductor and electronic ...

>read more